On-floor scissor lift
Safety features:
Precision safety locks
Synchronized hydraulic cylinder system…
Weight: 950 kg
+ More info
Professional electrohydraulic scissor lift with a 4,000 kg lifting capacity and 380 V three-phase power supply. Designed for automotive repair workshops, tyre centres and fast-fit services, it provides above-ground vehicle lifting without the need for a recessed installation pit. The lift features 2,020 mm platforms, a minimum height of 105 mm and maximum lifting height of 1,850 mm. Equipped with synchronised hydraulic cylinders, safety locks, lowering protection and four rubber vehicle support pads.
| Specification | Value |
|---|---|
| Model | EQT-40SLE-380 |
| Reference | 10/EQT-40SLE-380 |
| Lift type | Above-ground scissor car lift |
| Operating system | Electrohydraulic |
| Maximum lifting capacity | 4,000 kg |
| Power supply | 380 V three-phase · 50/60 Hz |
| Listed motor power | 2.2 kW |
| Maximum lifting height | 1,850 mm |
| Minimum height | 105 mm |
| Platform length | 2,020 mm |
| Synchronisation | Synchronised hydraulic cylinders |
| Safety locking | Precision mechanical locks |
| Safety catch release | Compressed air operated |
| Hydraulic protection | Safety valve |
| Lowering safety | Safety stop with alarm |
| Travel limit | Upper limit switch |
| Included accessories | 4 rubber lifting pads |
| Installation | Above-ground, no recessed pit |
| Recommended use | Automotive maintenance, repairs, brakes, tyres and underbody inspections |
Requires a stable, level workshop floor with adequate load-bearing capacity and fixing conditions in accordance with the manufacturer's instructions. No recessed installation pit is required.
A 380 V three-phase electrical supply and an air compressor are needed to operate the safety lock release. Confirm the required air pressure and fittings.
The commercial listing recommends an air compressor with a tank of at least 100 litres, depending on the intended duty cycle.
Installation, connections, commissioning and safety inspections must be carried out by qualified personnel following the specific EQT-40SLE-380 installation manual.
Capacity 10 Tons
Dimensions 68 x 45 x 107 cm
Stroke 17.5 cm
Distance between columns 29 cm
Weight 53 Kg
This car lift operates electro-hydraulically. It has been designed to work with medium and small-sized vehicles.
This car lift operates electro-hydraulically and is designed to work with medium and small-sized vehicles in garages and workshops.
Capacity: 1.5 tons
Maximum height: 110 cm
Approximate dimensions: 111 x 73 x 30 cm
REQUIREMENTS
The installation of this equipment must be carried out on a perfectly level floor.
Pneumatic Scissor Lift
Safety Features:
This car lift operates electro-hydraulically and has been designed to work with medium and small-sized vehicles with…
This car lift operates using an electro-hydraulic system. It is designed to work with medium and small-sized vehicles with a maximum total weight of 4 tons in garages and workshops.
This Car lift electro-hydraulic lift operation is designed to work with vehicles of medium and small size with a maximum total weight of 4t in garage…
Car lift with electro-hydraulic lifting system, designed to operate with small and medium-sized vehicles with a maximum total weight of 5 tons in garages and workshops.
Portable single scissor lift 3 tons
2-post clear-floor car lift with overhead gantry, 220V, and 6-ton capacity, designed for professional workshops that need to lift heavy vehicles with safety, stability, and ease of use. Its clear-floor design allows smooth movement between posts and improves access to the vehicle's undercarriage, while the electro-hydraulic system, electrical safety lock release, and automatic safety locks let you work with confidence during mechanical repairs, maintenance, tire changes, brakes, suspension, and underbody inspections. A robust solution for workshops handling large SUVs, vans, and light commercial vehicles.
Capacity: 1 ton
Minimum height: 52 cm
Maximum height: 128 cm
Packing dimensions: 188 x 82.5 x 40 cm
Adjustable width: 42 - 124 cm
The lift is supplied without any type of fluid
It can be used for lifting with: ratchet, crank, or impact gun
Dimensions 1…
Pneumatic scissor lift
Safety features:
This Car lift electro-hydraulic lift operation is designed to work with vehicles of medium and small size with a maximum total weight of 4t in garage…
2-post 6-ton clear-floor car lift 380V, designed for professional workshops that need to raise heavy vehicles with safety, stability, and comfort. Its clear-floor structure facilitates easy passage between posts and improves access to the underside of the vehicle, while the electro-hydraulic system, electric safety release, and automatic safety locks allow technicians to work with confidence during mechanical, maintenance, tire, brake, suspension, and underbody inspection operations. A robust solution for workshops servicing large SUVs, vans, and light commercial vehicles.
